The -m vcs option specifies the VCS cluster monitor, which implies the existence of the cluster configuration file /etc/VRTSvcs/conf/config/main.cf. The command causes vxclustadm to re-read the cluster configuration file, and implement any required changes to the membership of the cluster. Rename the node updated in step 6 following Microsoft guidelines and reboot. Default location: C:\Program Files\Veritas\cluster server\conf\config. Open main.cf file in a text editor and perform 'find and replace' to replace the old node names with the new ones for all occurrences. Table: Cluster status messages shows the various messages that may be output according to the current status of the cluster node. Perform these steps on one node in the cluster. To determine whether the vxconfigd daemon is enabled and/or running, use the following command: vxdctl -c mode. Reinit allows nodes to be added or removed from a cluster dynamically, without stopping the cluster. The -c option can be used to request cluster information and to find out which node is the master. 1 orbs: node: circleci/email protected aws-cli: circleci/email. # /etc/vx/bin/vxclustadm/vxclustadm -m vcs reinitģ. The following get-login-password displays a password that you can use with a container. To update status of the nidmap, on the remaining nodes of the existing cluster, run the following commands By default, this is located at /etc/VRTSvcs/conf/config. Remove any references to the removed node from the main.cf. The removed node shows status = "Out of Cluster" as expected.Ģ. Identify the VMkernel port used for vSAN, its IP address, and the node UUID on each host. Nebula 4 1 Out of Cluster << removed from cluster The following are 30 code examples for showing how to use uuid. Though any node can initiate an operation to create, delete, or resize data, the master node carries out the. # /etc/vx/bin/vxclustadm vxclustadm nidmap The CFS is designed with master/slave architecture. The current active nidmap is displayed by running Note: DO NOT renumber the node id's to make them sequential. Remove the entire line "1 nebula" on all nodes. On each of the existing nodes, edit the /etc/llthosts file to remove lines that contain references to the removed nodesįor example, to remove a node called "nebuma," update the /etc/llthosts file as follows: The system should then startup okay.As part of removing a node from a cluster, the /etc/llthost file needs to be edited on all hosts in the clusterġ. Check the NetBackup resource to see if it is now probed ( hares -display nbu_server | grep -i Probed ). Often the problem is not being able to start the NetBackup resource (default name: nbu_server).Īfter the High Availability ' had ' services are stopped, then restart the problematic node first ' hastart '. ' hastop -local -force ', on the active node (where the problems are occurring). After the High Availability ' had ' services are stopped, then restart the problematic node first ' hastart '. Often the problem is not being able to start the NetBackup resource (default name: nbuserver). Group System Probed AutoDisabled Stateĭ nbu_group NetBackup nbu_server -sys ) fails to help resolve the issue, on the node which is not Probed and fails to start the NetBackup resource, either stop all resources or manually start the resources which NetBackup is dependent on, then ' hastop -local ' on inactive node(s) ' hastop -local -force ', on the active node (where the problems are occurring). Deportand import the shared DG on the current CVM Master node. Confirmthe SG is offline on all the nodes. Nbu_server ResourceInfo global State Stale Msg TS cfs cvmonline local firm < There are no Parent SG for cfs, so no need to offlinethem. implemented in SmartCopilot: Master-Slave aircraft position is calculated. Nbu_server RSPFile global /usr/openv/netbackup/bin/cluster/NBU_RSP Both the stock and the barrel/receiver show significant wear, however this. Command vxdctl -c mode, will show you which node is the master. Nbu_server ArgListValues NBUMaster "" NONE /usr/openv/netbackup/bin/cluster/NBU_RSP nbu_group If you shutdown VCS on a node it is all sorted out for you - i.e any filesystems that.
0 Comments
Leave a Reply. |